UPT Perpustakaan UM

  • Beranda
  • Informasi
  • Repository UM
  • SIPADU UM
  • OPAC SIPADU

Pencarian Spesifik

Pencarian berdasarkan :

SEMUA Pengarang Subjek ISBN/ISSN Pencarian Spesifik

Pencarian terakhir:

{{tmpObj[k].text}}
No image available for this title

Tugas Akhir

Analysis of the mechanical strength comparison between grid infill and honeycomb infill structures in 3d printing / Ahmad Muwaffaq Afif

Afif, Ahmad Muwaffaq - Nama Orang;

Abstrak
This study aims to analyze and compare the mechanical strength of two types of infill structures namely grid and honeycomb in 3D printed products using PLA filament. The primary objective is to determine the differences in tensile strength performance material usage efficiency and printing time between these two infill patterns at various infill percentages and nozzle temperatures. The study is expected to provide recommendations for selecting the optimal infill structure based on mechanical strength requirements material efficiency and production time in 3D printing applications. In the era of Industry 4.0 3D printing technology is increasingly utilized in The research employed an experimental method with a quantitative approach. The study began with fabricating tensile test specimens using an Ender-3 V3 SE 3D printer with two infill patterns grid and honeycomb at infill percentages of 20% 30% 40% and 50% and nozzle temperatures of 200 deg C and 210 deg C. The specimens were designed according to ASTM D638 Type V standards using Autodesk Inventor software. After printing tensile strength tests were conducted using a Universal Testing Machine (UTM) to measure ultimate tensile strength elongation at break and elastic modulus. The collected data were statistically analyzed to compare the performance of both infill structures and to evaluate material usage efficiency and printing time. The results indicate that the grid infill structure exhibits higher ultimate tensile strength compared to the honeycomb structure across all tested infill percentages and nozzle temperatures. For example at 200 deg C and 50% infill the grid structure achieved a maximum tensile strength of 47.1 MPa while the honeycomb structure reached 42 MPa. However the honeycomb structure demonstrated higher elongation at break and elastic modulus indicating better flexibility and deformation capacity especially at low to medium infill levels. In terms of material efficiency the grid structure produced lighter specimens than the honeycomb at the same infill percentage making it more material-efficient. Additionally the printing time for the grid structure was consistently shorter than that of the honeycomb with the time difference increasing as the infill percentage rose. In conclusion the grid pattern excels in tensile strength and printing time efficiency whereas the honeycomb pattern offers superior flexibility and deformation efficiency. Therefore the choice of infill pattern should be tailored to the specific application requirements.


Informasi Detail
DDC
-
Prodi
Universitas Negeri Malang. Program Studi Teknologi Rekayasa Manufaktur, 2025.
Deskripsi Fisik
xv, 56 hlm. : ilus
Bahasa
No Reg
0137/TA/25
Edisi
Tugas Akhir (Diploma)--Universitas Negeri Malang. 2025
Subjek
1. 3D PRINTING - STRUKTUR INFILL (GRID DAN HONEYLOMB)
2. SIFAT MEKANIK - UJI TARIK (TENSILE TEST)
3. TEKNOLOGI REKAYASA MANUFAKTUR - ANALISIS EKSPERIMENTAL
4. 3D PRINTING - INFILL STRUCTURE (GRID AND HONEYLOMB)

Pembimbing
1. Didin Zakariya Lubis, S.pd, M.eng
Lampiran Berkas
You must be logged in to get fulltext


UPT Perpustakaan UM
  • Berita

Tentang Kami

TIM IT Perpustakaan 2023

Cari

masukkan satu atau lebih kata kunci dari judul, pengarang, atau subjek

Donasi untuk SLiMS

Pilih subjek yang menarik bagi Anda
  • Karya Umum
  • Filsafat
  • Agama
  • Ilmu-ilmu Sosial
  • Bahasa
  • Ilmu-ilmu Murni
  • Ilmu-ilmu Terapan
  • Kesenian, Hiburan, dan Olahraga
  • Kesusastraan
  • Geografi dan Sejarah
Icons made by Freepik from www.flaticon.com
Pencarian Spesifik