UPT Perpustakaan UM

  • Beranda
  • Informasi
  • Repository UM
  • SIPADU UM
  • OPAC SIPADU

Pencarian Spesifik

Pencarian berdasarkan :

SEMUA Pengarang Subjek ISBN/ISSN Pencarian Spesifik

Pencarian terakhir:

{{tmpObj[k].text}}
No image available for this title

Skripsi

Comparison of multi-core and single-core balsa cfrp sandwich composite: mechanical behavior and fea-based optimization for an energy-efficient vehicle steering wheel / Muhammad Tegar Aditiyah

Aditiyah, Muhammad Tegar - Nama Orang;

Abstrak
The development of lightweight yet structurally rigid components is critical for energy efficient competition vehicles such as those entered in the Energy Efficient Car Contest (KMHE). This study investigates the effect of balsa core thickness and carbon fiber reinforced polymer (CFRP) skin layer configuration on the mechanical performance of sandwich composites intended for a competition-vehicle steering wheel. Six configurations were fabricated by Vacuum Assisted Resin Infusion (VARI) comprising three multi-core (Samples 1 ndash 3) and three single-core (Samples 4 ndash 6) layouts with balsa core thickness varied from 6 to 10 mm and CFRP skin layer counts ranging from 8 to 24. Density three-point flexural (ASTM D7264) tensile (ASTM D3039) and Charpy impact (ASTM D6110-17) tests were performed and the resulting properties were used as input for ANSYS Static Structural analysis of the steering-wheel geometry under a quasi-static torque of 7.57 N middot m with a safety factor of 3. Multi-objective optimization via Pareto-front analysis was applied to balance structural mass and maximum von Mises equivalent stress. The measured density ranged from 457.55 plusmn 16.83 to 877.97 plusmn 45.21 kg/m sup3 substantially below aluminum (2 700 kg/m sup3 ) and steel (7 800 kg/m sup3 ). Sample 1 produced the highest flexural strength (683.30 MPa) tensile strength (159.10 MPa) and absorbed impact energy (27.31 J) whereas the Pareto-front analysis identified Sample 3 as the optimal configuration with a mass of 0.170 kg maximum von Mises stress of 1.08 MPa safety factor of 54.97 and maximum deformation of 0.346 mm. Compared with the equivalent single-core configuration (Sample 6) the multi-core arrangement of Sample 3 achieved a 2.86% mass reduction without compromising stress capacity owing to the shorter effective buckling length of each sub-core. The results confirm the viability of balsa ndash CFRP sandwich composites as a lightweight structurally efficient material for energy-efficient vehicle steering wheels.


Informasi Detail
DDC
SKRIPSI DIGITAL
Prodi
Universitas Negeri Malang. Program Studi Teknik Mesin, 2026.
Deskripsi Fisik
23 hlm. : ilus
Bahasa
No Reg
3022/RS/26
Edisi
Skripsi (Sarjana)--Universitas Negeri Malang. 2026
Subjek

Pembimbing
1. Rr. Poppy Puspitasari, S.pd, M.t., Ph. D
Lampiran Berkas
You must be logged in to get fulltext


UPT Perpustakaan UM
  • Berita

Tentang Kami

TIM IT Perpustakaan 2023

Cari

masukkan satu atau lebih kata kunci dari judul, pengarang, atau subjek

Donasi untuk SLiMS

Pilih subjek yang menarik bagi Anda
  • Karya Umum
  • Filsafat
  • Agama
  • Ilmu-ilmu Sosial
  • Bahasa
  • Ilmu-ilmu Murni
  • Ilmu-ilmu Terapan
  • Kesenian, Hiburan, dan Olahraga
  • Kesusastraan
  • Geografi dan Sejarah
Icons made by Freepik from www.flaticon.com
Pencarian Spesifik